Unlike conventional magnetic and gyro compasses, accuracy is not affected by G-force or velocity. Furthermore, when compared to other GPS based compass systems incorporating only two antennas, our addition of a third GPS antenna provides enhanced accuracy while reducing the negative effects of pitch, roll, and yaw. Multiple, programmable high-speed heading data outputs allow you to send this information where you need it, and our unique Analog Pitch and Roll Output can be used to enhance your Furuno Sonar System.
This Satellite Compass is ideal as an alternative to a traditionally expensive and high-maintenance gyrocompass for non-compulsory vessels, as well as being the perfect back up solution to a gyro for a compulsory vessel.
No Longer Available. Display Size 4. Receiver Type 26 inch Dome. Cover the antenna connectors with vulcanizing tape and vinyl tape, for waterproofing. Tie tape ends with a cable tie. Set the joints of the coaxial cables into the cavity in the antenna base. Pass two cable ties long life, temperature resistant type, local supply through the hole shown in the figure below. Fasten them at the locations shown in the figure below.
Use the paper pattern to position the fixtures. Follow paragraph 1. If OK is not displayed, relocate the antenna. Screw in three antenna elements in the Antenna Base. Remove Antenna Cover and Arm Cover. Pass the coaxial cable from each antenna element through the center of the respective arm and then through the hole at the center of the antenna unit. Orient the three antenna elements so that the protrusion on each faces the bow.
Making sure each antenna element is correctly oriented, fix each with its nut. Write the corresponding arm number on each coaxial cable, using a magic marker. When connecting with the coaxial cables from the processor unit it is necessary to match correct antenna element number with coaxial cable color. Temporarily fix the pedestal and support plate to the antenna mast as shown in the illustration below. The pedestal and support plate will be welded to the antenna mast after confirming that the installation site is suitable, following paragraph 2.
Note: If U-bolts are used to temporarily fix the pedestal and support plate, DO NOT overtighten them — overtightening may deform the pedestal. Antenna Mast Local supply. Flat Washer. The bow mark is between antenna element [1] and [2]. Face the bow mark towards the bow. Follow the instructions in the paragraph 2. Weld the antenna unit to the antenna mast as shown in the next paragraph.
Unfasten the coaxial cables and dismount the antenna unit. Weld the pedestal and support plate to the antenna mast. Remove the clamps used to temporarily fasten the pedestal and support plate. Fasten the coaxial cables and fix the antenna unit. Wrap the antenna connector with self-vulcanizing tape and then vinyl tape for waterproofing as shown in the illustration below. Tie tape ends with cable ties to prevent unraveling. Look at the heading indication on the display. Make a loop in the antenna cable as shown in the illustration below.
Fasten the antenna cable to the antenna mast with cable ties. Coat bolt threads with Three Bond. Fasten bolt with nuts and then coat nuts with Three Bond also. Coat bolt threads and nuts at the bottom of each antenna element with Three Bond Paint pedestal and support plate with anti-corrosive paint. Bird-repellent fixture. It can be mounted on the deck, bulkhead, or on the underside of a desk. The processor unit is shipped from the factory ready for bulkhead mounting. Orient the processor unit as shown below and fix it to the mounting location with four tapping screws M5x You will set the orientation later on the menu.
The processor unit may be mounted on the underside of a desk as shown in the figure below. Do not install it on the overhead. Fasten the hanger to the mounting location with four tapping screws supplied. See the outline drawing for mounting dimensions. Screw the knobs into the display unit. Set display unit to the hanger and tighten the knobs.
Two types of flush mounts are available. See the outline drawing at the back of the manual for details. Make a cutout in the mounting location. The dimensions are W x 92 H mm.
Fasten the cosmetic panel to the display unit with hex bolts and spring washers. Fasten the display unit to the mounting location with tapping screws. Place the display unit in the cutout. Fix the display unit to the two flush mount fixtures with hex bolts and spring washers.
Screw the butterfly nut on the butterfly bolt. Fix the display unit with the butterfly bolt and then tighten the butterfly nut. This section covers general wiring. For further details see the interconnection diagram at the back of this manual. Note 2: The optional antenna cable set CP or CP allows you to extend antenna cable length to 30 m 50 m.
See next page for how to attach the connector. Slip the pin onto the conductor. Solder them together through the hole on the pin. Screw the clamp nut into the shell. Tighten by turning the clamp nut. Do not tighten by turning the shell. In this condition it takes about 12 minutes to find heading.
If OK is not displayed within 30 minutes after turning on the power, the antenna mounting location may not be suitable.
Suspect that the number of satellites in view is less than five due to signal blockage. For the open-type antenna, loosen the nut at the center of the antenna unit to adjust antenna orientation. Resolve the problem and then recheck tracking status. Refer to section 1. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password?
Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Sc Furuno Sc 50 User Manual Download for 1. The paper used in this manual is elemental chlorine free. Only qualified personnel should work inside the equipment.
Do not disassemble or modify the equipment. Fire, electrical shock or serious injury can result. Do not place liquid-filled containers on the top of the processor unit. Fire or electrical shock may result if the liquid enters the equipment. Use the proper fuse. Use of a wrong fuse can damage the equipment and cause fire.
Fire or electrical shock can result if the power is left on. Do not install the equipment where it may get wet from rain or water splash. No user-serviceable Type: parts inside. Code No. Considerations 1. Antenna unit 1. Display unit, processor unit 1. Antenna unit SC - 1. Bulkhead mount 1. Deck mount 1. Installation on the underside of a desk 1. Desktop, overhead mounting 1. Flush mount 1. Confirming satellite status 1. Choosing mounting method 1. General wiring 1. Display Contrast 2.
Description of displays 2. Setup 2. Satellite Status 2. Displaying the GPS setup menu 2. Data 2. Heading 2. Log pulse 2. Geodetic data 2. Units of measurement 2.
Using local time ii. AP-1 1. AP-1 2. AP-2 3. AP-8 4.
0コメント